Floor Stripping and Waxing

If you manage a commercial building in Metro Detroit, the tile floors in your lobbies, hallways, and work areas take more abuse than almost anything else you maintain. Floor stripping and waxing is the heavy maintenance that keeps those floors serviceable — removing worn, yellowed finish down to bare tile and rebuilding it with fresh coats. This guide covers what the process actually involves, when a facility needs it, what's included in a commercial job, what drives cost, how the work gets scheduled around an occupied building, and how to get a walkthrough booked. It's written for facilities managers and building owners. This is commercial work only — Best Choice Janitorial Services does not take residential jobs.

What floor stripping and waxing actually is

Most commercial tile floors — vinyl composition tile (VCT) being the most common — are protected by a sacrificial layer of floor finish, often called wax. That finish is meant to take the wear so the tile doesn't. Dirt, foot traffic, rolling carts, and tracked-in debris grind into it over months and years. Buffing or burnishing shines what's there. Scrubbing and recoating cleans the top layer and adds a fresh coat. But eventually the finish itself is the problem: it's yellowed, embedded with soil, worn through in traffic lanes, or built up unevenly from years of partial fixes.

Stripping is the reset. The crew applies a chemical stripper to soften the old finish, mechanically scrubs it off with a rotary machine, removes the slurry with a wet vacuum, rinses and neutralizes the floor, and then lays down new coats of sealer and finish. Done right, you're back to a clean, uniform surface with a consistent number of coats across the whole floor — not patchwork.

The distinction matters commercially. A floor that needs a full strip won't be fixed by another coat of wax on top. You'll just be sealing in the discoloration and spending money on a finish job that won't hold.

Signs your facility needs a full strip

Walk your own floors and look for these:

In this region there's also a seasonal factor. Michigan winters mean road salt, and salt tracked across a finished floor is aggressive — it abrades the finish and leaves haze that normal cleaning doesn't fully reverse. A lot of Metro Detroit facilities schedule stripping work in spring precisely because of what winter did to the floors. If your floors looked noticeably worse in March than they did in October, that's usually why.

What a commercial job includes

A proper commercial floor stripping and waxing job is more than a machine and a bucket. Expect the following scope:

  1. Site walkthrough and measurement. Square footage, floor type, coat count, access constraints, and schedule are all determined on site.
  2. Area prep. Furniture, mats, and movable fixtures relocated; work zone taped or coned off; adjacent areas protected.
  3. Dry soil removal. Dust mopping and vacuuming so grit doesn't get scrubbed into the tile.
  4. Stripper application and dwell. Chemical applied section by section and given time to soften the old finish — typically somewhere in the range of five to fifteen minutes depending on the product and buildup.
  5. Machine scrubbing. Rotary machine with a stripping pad, working the old finish loose, with edges, corners, and baseboards detailed by hand where the machine can't reach.
  6. Slurry removal and rinse. Wet vacuum pickup, followed by a thorough rinse and a neutralizing rinse so the new finish bonds correctly. Residue left behind is a common cause of peeling.
  7. Drying. The floor must be completely dry before the first coat.
  8. Finish coats. Thin, even coats laid with a clean mop, with dry time between each — commonly twenty to forty-five minutes per coat depending on humidity and airflow.
  9. Cure and reopen. Light foot traffic is often possible within hours of the final coat; full cure before heavy traffic, cart traffic, or wet cleaning typically runs twenty-four to forty-eight hours.

How Best Choice Janitorial Services performs the work

Best Choice Janitorial Services is a commercial-only cleaning company serving Metro Detroit, and commercial floor stripping and waxing is one of its core services alongside general commercial cleaning, carpet cleaning, upholstery cleaning, appliance cleaning, commercial kitchen steam cleaning, pressure washing, and full commercial janitorial programmes.

The job starts with an on-site walkthrough — always. Nobody can price or scope a strip-and-wax over the phone, because the variables that determine the work (condition, coats, obstacles, access hours) only show up in person. During the walkthrough the crew lead checks the floor type, measures the areas, tests how much old finish is on the tile, and talks through scheduling with you.

On the work night, the process follows the scope above: prep, strip, detail, rinse, neutralize, dry, coat. Coat count is agreed in advance based on traffic level and floor condition rather than defaulted to a one-size number. The crew works in sections so the building stays navigable, and the floor stays closed off until the finish has cured enough to open safely.

One scope note worth stating plainly: hood and duct cleaning for commercial kitchens is a separate certified trade, and Best Choice Janitorial Services does not offer it. If your project involves a kitchen, the floors and general surfaces can be handled; the exhaust system needs a certified specialist.

How many coats your floor needs

Coat count isn't a marketing decision — it's driven by traffic and current condition. More coats means more finish depth, which means longer wear life in heavy-traffic zones. Typical commercial practice looks like this:

Traffic level Typical finish coats Typical full-strip interval
Light (private offices, low-use corridors) 2–3 Roughly 18–24 months
Moderate (general office hallways, common areas) 3–4 Roughly every 12 months
Heavy (entries, retail floors, schools, corridors) 4+ Roughly 6–12 months, with interim scrub-and-recoats

Two caveats. First, a floor that's been neglected — or stripped for the first time in years — may take an extra coat or two on the initial rebuild, because bare or porous tile drinks up the first coats. Second, heavy-traffic facilities usually get better economics from a full strip paired with interim scrub-and-recoats between cycles, rather than paying for full strips twice a year.

Scheduling work around an occupied building

This is the part that makes facilities managers nervous, and it's the reason almost all commercial stripping and waxing happens after hours. The floor has to stay completely clear while coats dry and cure. That means no foot traffic, no carts, no chairs sliding across a tacky finish — one shortcut across a half-cured floor can mark every coat and force a redo.

Practical scheduling looks like this:

When people search for floor stripping and waxing Metro Detroit facilities can schedule without shutting down, the honest answer is: you don't schedule it without some closure. What a good contractor does is compress the disruption — nights, weekends, phased sections — so the building never stops functioning.

What drives the cost

Best Choice Janitorial Services does not quote firm prices without a walkthrough — that's policy, not a sales tactic. But you can understand what moves the number before you book one:

For ballpark planning across the commercial market, full strip-and-wax work is commonly quoted somewhere in the range of roughly $0.75 to $2.00 per square foot depending on the factors above, with scrub-and-recoat maintenance coming in well under that. Most contractors also carry a minimum charge so small jobs are worth mobilizing for. Treat those ranges as planning numbers only — your actual price comes from the walkthrough.

Who this service is for

Best Choice Janitorial Services performs this work for offices, hospitals and medical facilities, industrial and manufacturing buildings, schools, retail spaces, and essentially any commercial property in Metro Detroit. The common thread isn't the industry — it's the floor type and the traffic. If you have resilient tile in areas the public or your workforce uses daily, it will need this cycle eventually. Medical facilities and schools tend to run the tightest cycles because appearance standards and traffic are both high. Industrial buildings often need entry areas and corridors done while production floors may only need sealing.

What's consistently off the table is residential work. No houses, no garages-at-home, no exceptions.

How to request a walkthrough

Getting a quote for commercial floor stripping and waxing is straightforward:

  1. Pull your basics. Approximate square footage of the areas in question, the floor type if you know it, and how long it's been since the last full strip.
  2. Note the problem areas. Which corridors, entries, or rooms look worst. Photos help.
  3. Know your schedule constraints. Nights that are off-limits, events on the calendar, security requirements, deadlines.
  4. Request the walkthrough. Contact Best Choice Janitorial Services through the website at https://jan.bestchoice411.com to set one up.

The walkthrough produces the scope, the coat recommendation, the schedule, and the price — in that order. If a stripping quote arrives without anyone setting foot in your building, that's a red flag regardless of who sent it.


Ready to get your floors evaluated?

If your floors are yellowed, worn through in the traffic lanes, or still showing what last winter's salt did to them, the fix is a full strip and rebuild — done after hours, on a schedule that keeps your building running, priced from an actual on-site walkthrough.

Request your walkthrough with Best Choice Janitorial Services today at https://jan.bestchoice411.com. Commercial only, Metro Detroit, no firm prices until we've seen the floor — because that's the only honest way to quote the work.