Nobody can give you a real number for this work over the phone. What affects the cost of floor stripping and waxing comes down to a handful of measurable things: the square footage, the condition the floor is in, how many coats of finish it needs, and when the work has to happen. Walk through those factors below and you'll be able to read any quote for what it actually covers — and understand why two bids for the "same" job can land in different places.
Area drives the obvious costs — stripper, pads, finish, labor hours. But size alone doesn't set the price. Ten thousand square feet of wide-open retail floor moves faster per square foot than three thousand square feet chopped up by offices, thresholds, and furniture. What matters is the production rate: how fast a crew can actually work the space. Large open expanses usually price better per square foot because setup and edge work spread across more area. Small, cut-up spaces carry more setup time per foot and price accordingly.
Stripping is the labor-heavy half of the job, and no two floors strip the same. A floor that's stayed on a maintenance schedule — routine burnishing, periodic scrub-and-recoat — usually strips clean in one or two passes. A floor that's been ignored for years, with yellowed, layered finish and dirt packed into the traffic lanes, takes extra passes, more aggressive pads, and more chemical. Entryways and restroom approaches are typically the worst of it. Condition also decides the scope: sometimes a scrub-and-recoat buys the floor another cycle at a lower cost and less downtime than a full strip. That call gets made on-site, looking at the tile.
Once the floor is stripped to bare tile, it gets rebuilt with coats of sealer and finish. That number isn't arbitrary. It follows traffic:
The tile itself factors in too. Porous or freshly stripped-back tile absorbs the first coats, so it takes more material to build a proper film. Three or four coats is common for moderate traffic; heavy-traffic zones often call for more. Every extra coat is material, labor, and dry time stacked onto the job, so an honest quote lines coat count up with how the floor actually gets used.
Finish doesn't just dry — it cures. Each coat needs its dry time before the next one goes down, and the final coats need to cure before the floor takes foot traffic, carts, or furniture weight. That's why commercial floor stripping and waxing usually happens after hours or over weekends: the floor has to stay completely clear while the coats cure, and overnight is the only window most occupied buildings can give up. If your facility can only open a tight overnight window, or the job has to be phased so one wing stays in service while another is worked, those constraints shape the schedule and the crew plan — and they show up in the price. After-hours and weekend labor is a real line item, not a rounding error.
Every square foot has to be clear before a strip pad touches it. If desks, shelving, display racks, or equipment have to come off the floor and go back afterward, that's labor on both ends of the job. Access matters too: a freight elevator and a long push from the dock slows production compared to a dock door next to the work area. Buildings that can be emptied, or worked room by room, run smoother and cost less than buildings where everything has to be shuffled around an occupied floor.
One flag worth raising here: if the tile or the old black adhesive under it is old enough to raise asbestos questions, that's an abatement issue handled by a licensed specialty contractor. It's not part of a strip-and-wax scope, and any reputable floor crew will stop and tell you so.
Vinyl composition tile (VCT) is the classic strip-and-wax floor, and most of what gets quoted is VCT. Sheet vinyl, linoleum, and some sealed concrete also take finish, but each responds differently to stripper chemistry and pad aggression, and a few specialty floors need specific products. The walkthrough establishes exactly what's down and what it can take.
Every factor above — condition, coat count, schedule, moves, floor type — has to be seen, not described over the phone. That's why Best Choice Janitorial Services quotes floor stripping and waxing only after an on-site walkthrough of the building. We serve commercial properties only across Metro Detroit: offices, hospitals and medical facilities, industrial and manufacturing buildings, schools, retail, and any other commercial property. No residential work. For the full process, from stripper to final cured coat, see the floor stripping and waxing overview.
Get a walkthrough, get a real quote
Best Choice Janitorial Services prices commercial floor stripping and waxing from an on-site walkthrough — never a firm number sight unseen. Metro Detroit, commercial buildings only. Request yours at https://jan.bestchoice411.com.