If you're comparing bids for commercial floor stripping and waxing, the line items matter more than the bottom number. Two quotes for the same floor can land far apart because one crew is quoting the full job and the other is quoting a quick refresher. This page lays out what's included in floor stripping and waxing when it's done right: the walkthrough, the prep, the strip, the rinse, the coats, and the cure time that keeps people off the floor afterward. For the wider picture on finishes, schedules, and maintenance cycles, see the Floor Stripping and Waxing overview.
A full job removes every bit of old finish down to bare tile, neutralizes and dries the floor, then rebuilds protection with several coats of sealer and finish. Anything less — a top-scrub and a couple of coats over existing finish — is a recoat, not a strip and wax. That distinction drives the price, so it's the first thing to pin down when comparing quotes.
Nothing gets priced until someone walks the floor. The walkthrough covers tile type, how much old finish is built up, staining and burns, furniture and fixtures, water access, and how the area gets used. That's what sets the coat count and the price. We don't quote firm numbers over the phone — commercial floor stripping and waxing gets priced from the floor itself.
Light furniture and equipment come off the floor; anything too heavy to move gets worked around by hand. The area gets dust mopped and vacuumed, baseboards and adjacent carpet get protected, and wet floor signage goes up before the first drop of stripper.
Stripper goes down per the label, dwells, and gets agitated with a low-speed machine and a stripping pad. The slurry gets wet-vacced up. Heavy buildup, burns, and old stains take extra passes. Edges, corners, and the bases of toilets and fixtures get hand work where the machine can't reach — this is where sloppy crews cut corners, and it shows for the life of the finish.
The floor gets rinsed, usually more than once, so no stripper residue is left behind. Residue trapped under new finish causes adhesion problems, dulling, and peeling. Then the floor dries completely before the first coat — laying finish over a damp floor is a guaranteed call-back.
New finish goes down in thin, even coats with a flat mop, with dry time between coats — commonly 30 to 45 minutes depending on airflow and humidity. Bare or badly worn tile gets sealer coats first, then finish coats on top.
High-speed burnishing after the finish cures adds gloss and hardness in high-visibility areas like lobbies and retail fronts. On some quotes it's a separate line item, so check whether it's in yours.
Crew and customer inspect together: coverage, edges, misses, furniture placement. The area stays taped off until the finish has cured.
The floor has to stay clear while the coats cure. A coat may be dry enough to re-enter carefully in under an hour, but the finished floor shouldn't take real traffic until it's fully cured — commonly a day before light traffic, and up to a few days before heavy traffic, equipment, or wet cleaning, depending on the product and conditions. Walking it too soon scuffs the finish and tracks debris into the coat, and nothing about that fixes itself.
That's why floor stripping and waxing is a nights-and-weekends job on occupied buildings. Crews strip and lay coats overnight, section by section, and the floor reopens in the morning with the tape still up in low-traffic spots for another day or two.
The coat count isn't a flat number — it follows traffic and floor condition:
Three to five coats is a common working range; heavy-traffic areas run toward the top of it. The walkthrough is what settles it.
To keep quotes honest, here's what sits outside this line item. Carpet cleaning, pressure washing, appliance cleaning, and kitchen steam cleaning are separate services we do offer, quoted on their own. Hood and duct cleaning is a separate certified trade and is not something we do. And everything we handle is commercial — no residential work, period.
We won't publish per-square-foot rates, because a rate only means something after the walkthrough. What moves it:
Two buildings with identical square footage can price differently for any of these reasons. That's the case for the walkthrough.
Daily dust mopping with the right mop, spills cleaned promptly, and neutral cleaner only — harsh chemicals eat the finish. Scheduled buffing or burnishing keeps the gloss up, and a top-scrub and recoat partway through the cycle buys time before the next full strip. The maintenance side is covered in the Floor Stripping and Waxing cluster overview.
Best Choice Janitorial Services handles commercial floor stripping and waxing across Metro Detroit — offices, hospitals and medical facilities, industrial and manufacturing buildings, schools, retail, and any commercial property. Commercial only, no residential. Hood and duct cleaning is a separate certified trade and is not offered.
Every price starts with an on-site walkthrough. No firm quotes over the phone.
Schedule yours: https://jan.bestchoice411.com